Often asked: How Much Stain For Fence?

How do I calculate how much stain I need for my fence?

Divide the total square feet of fence to be stained by the coverage listed on the can. For example, if you have 1,000 square feet of fence and the stain says that 1 gallon covers 200 square feet, you would divide 1,000 by 200, which equals 5 gallons to cover the fence.

Is it better to spray or roll stain on a fence?

Spraying vs. I recommend using an airless sprayer when applying wood fence stain. Using only a brush and roller for this project is extremely time-consuming and labor-intensive. Use a sprayer to quickly apply the material on the surface and a brush and roller to push the material into the wood.

How many sq ft does a gallon of stain cover?

Once this calculation is considered, you can figure out how many gallons of deck stain you need by reading the coverage rate of the stain you are buying. On average most deck stains cover 150-300 sq. ft. per gallon depending on the age, condition, and porosity of the wood.

You might be interested:  FAQ: How Many Bags Of Concrete For A Fence Post?

Is it worth it to stain a fence?

A wood fence provides privacy, security and a great focal point for your property. Routine wood fence maintenance is important to maintain the aesthetic of the fence and the life of the wood. A fence should be stained every two to three years to preserve the look and function of the fence.

How do you prepare a fence for staining?

Clean the fence surface by applying a cleaner — a small solution of soapy bleach water may be all you need, but seek out a fence/deck cleaner for tough stains. Scrub with a stiff bristle brush to remove dirt, debris, and mildew. Rinse thoroughly with a high pressure nozzle attached to a hose or a pressure washer.

Do you stain both sides of a fence?

While you should always follow the manufacturer’s recommendations, the general rule is that wood fences should be stained every five years and sealers should be applied every two to three. Of course, if you are staining and sealing it makes sense to seal after staining and vice versa.

Can I use a roller to stain a fence?

If using a roller, opt for a medium nap roller cover, then fully saturate the nap with the stain. Apply the stain in two- to three-foot sections of the fence at a time, taking care to back-brush, or re-paint over uncovered areas left by the previous stroke, with a wide brush.

Can I use a sprayer to stain my fence?

While some may think staining a fence can take an entire Saturday, with the right prep and a pump sprayer you can achieve gorgeous results in a very short amount of time. Some stain is meant to be applied with a brush and roller, and some are perfectly fine to apply with a pump sprayer.

You might be interested:  Readers ask: How To Install Privacy Fence Panels?

How much does a gallon of stain cost?

A gallon of stain costs $20 to $50, which covers 200 to 300 square feet. Get free estimates from deck staining companies near you or view our deck stain cost calculator below.

How much does 8 oz of stain cover?

Easy to use wood finish covers up to 70 sq. ft. per 8 oz.

Do you need two coats of semi-transparent stain?

With a solid stain, CR typically recommends putting on two coats because these are more like a regular paint and will dry one on top of the other. But with a clear or semi-transparent wood stain, a second coat will just sit on the surface of the first coat.

Does staining a fence protect it?

Painting or staining a wood fence can help your fence last longer and look better. Either one will extend the lifespan of your fence by giving it some protection against rot, insects, wear, and tear. Wood absorbs stain much deeper than it does paint.

Should you pressure wash fence before staining?

Before applying any type of finish to a fence, including stains, you need to remove any old finish(es) and remove any built up dirt, dust, grime or other substances from the fence. Pressure washing a fence before staining it will also ensure blemishes are removed that could show through the surface of the stain.

How long should you wait before staining a new fence?

Consider the type of wood, and then wait the proper amount of time (usually anywhere between 1 and 6 months ) before staining or sealing your fence. This will allow it to sufficiently weather and to dry or cure.

Leave a Reply

Your email address will not be published. Required fields are marked *